{"id":7689,"date":"2026-03-21T21:33:28","date_gmt":"2026-03-21T21:33:28","guid":{"rendered":"https:\/\/sawahsolutions.com\/range\/4-reasons-rifle-magazines-fail-and-how-to-choose-a-better-one\/"},"modified":"2026-03-21T21:33:28","modified_gmt":"2026-03-21T21:33:28","slug":"4-reasons-rifle-magazines-fail-and-how-to-choose-a-better-one","status":"publish","type":"post","link":"https:\/\/sawahsolutions.com\/range\/4-reasons-rifle-magazines-fail-and-how-to-choose-a-better-one\/","title":{"rendered":"4 Reasons Rifle Magazines Fail\u2014and How to Choose a Better One"},"content":{"rendered":"
<\/p>\n
\n

Unreliable rifles are the worst. Whether it\u2019s a bolt-action or semi-auto, a rifle that doesn\u2019t load cartridges smoothly and quickly can put a real damper on a trip to the range or the field. Most hunters point the finger at some component of the firearm itself, but the real culprit is probably something much simpler and easier to fix: the magazine.<\/p>\n<\/div>\n

\n

Whenever someone tells me about an unreliable rifle, the magazine is always the first thing I recommend changing. Eight times out of 10, that\u2019s the real problem: the feed lips have cracked, the spring has worn out, or the follower is poorly designed.<\/p>\n<\/div>\n

\n

It\u2019s best to select a high-quality magazine from the outset so you never have to deal with reliability issues in the first place. The problem is, they all look pretty much the same from the outside. How can you sort the wheat from the chaff without finding out the hard way? That\u2019s the question I aim to answer below.<\/p>\n<\/div>\n

\n

<\/source><\/source><\/source><\/source><\/picture><\/p>\n<\/div>\n

The Parts of a Magazine<\/h3>\n<\/p>\n
\n

Rifle magazines incorporate a ton of geometrical engineering, but they don\u2019t have many parts.<\/p>\n<\/div>\n

Body<\/h3>\n<\/p>\n
\n

\"Body<\/source><\/source><\/source><\/source><\/picture><\/p>\n<\/div>\n

\n

The body of the magazine houses all the components and determines durability and geometry. It\u2019s usually constructed from steel, aluminum, or polymer.<\/p>\n<\/div>\n

Feed Lips<\/h3>\n<\/p>\n
\n

\"Feed<\/source><\/source><\/source><\/source><\/picture><\/p>\n<\/div>\n

\n

The feed lips are incorporated into the body, and they\u2019re one of the most critical features. They keep cartridges from being pushed out the top of the mag and hold them in place to be stripped by the bolt.<\/p>\n<\/div>\n

Spring<\/h3>\n<\/p>\n
\n

\"Spring<\/source><\/source><\/source><\/source><\/picture><\/p>\n<\/div>\n

\n

The spring provides the upward pressure pushing the next cartridge into position after the top one is stripped and loaded.<\/p>\n<\/div>\n

Follower<\/h3>\n<\/p>\n
\n

\"Follower<\/source><\/source><\/source><\/source><\/picture><\/p>\n<\/div>\n

\n

The follower is the flat(ish) piece attached to the spring on which the cartridges rest.<\/p>\n<\/div>\n

Bottom Metal<\/h3>\n<\/p>\n
\n

This is the piece on the bottom of the magazine that holds the spring in place (it doesn\u2019t have to be made of metal).<\/p>\n<\/div>\n

Why Do Magazines Fail?<\/h3>\n<\/p>\n
\n

Mag failures are a greater concern in semi-automatic rifle platforms than bolt- or lever-action, but it\u2019s always a headache to clear a jam. And if you think all magazines are created equal, consider this: the U.S. Army deployed an improved M-16\/M-4 magazine in 2009 that reduced the risk of magazine-related stoppages by more than 50%<\/em>. With that kind of reliability improvement on the table, it\u2019s worth figuring out why magazines fail.<\/p>\n<\/div>\n

\n

Here are four of the most common reasons.<\/p>\n<\/div>\n

\n

1. Cracked, Worn-Out Feed Lips<\/strong><\/p>\n<\/div>\n

\n

Faulty feed lips can\u2019t contain the spring\u2019s tension and allow cartridges to pop out the top of the magazine. Rounds can jump out if a loaded mag is jostled in a bag or case, or even while the rifle is cycling. The latter scenario can result in jams and double feeds.<\/p>\n<\/div>\n

\n

Feed lips can wear out or crack with heavy use, or they can slowly spread out if you store magazines fully loaded for an extended period of time.<\/p>\n<\/div>\n

\n

\"Feed<\/source><\/source><\/source><\/source><\/picture><\/p>\n<\/div>\n

\n

This is one way you can identify a high-quality magazine. The feed lips on Magpul\u2019s Gen 2 PMAGs would crack if stored fully loaded, but the Gen 3 version fixed this problem, and I\u2019ve never had any problems.<\/p>\n<\/div>\n

\n

\"Feed<\/source><\/source><\/source><\/source><\/picture>\nThe feed lips on the Gen 2 PMAG (right) would sometimes crack. Magpul redesigned this section of the mag body for the Gen 3 PMAG (left), which fixed the issue.<\/span><\/p>\n<\/div>\n

\n

To test if the feed lips on a magazine are still functioning properly, load a mag to the top and tap the bottom on the ground with some force. If a round pops out, it might be time to throw that mag in the bin and replace it.<\/p>\n<\/div>\n

\n

2. Poorly Designed Follower<\/strong><\/p>\n<\/div>\n

\n

The follower is where the magic happens from an engineering perspective. The primary purpose of a follower is to keep the cartridges at the correct angle as they move up the magazine. If a cartridge arrives at the top at the wrong angle, it will almost certainly jam as the bolt attempts to strip it off. The bullet might get stuck going up the feed ramp or nosedive into the front of the magazine.<\/p>\n<\/div>\n

\n

\"Follower<\/source><\/source><\/source><\/source><\/picture><\/p>\n<\/div>\n

\n

It\u2019s tough to tell whether a follower is well-designed without using it, but there are a few features you want to look for. The most important is \u201canti-tilt.\u201d When you press the front or back of the follower, it shouldn\u2019t move very much. It should stay flat, which will ensure that the cartridges do the same. Modern designs use extended front and rear legs to keep the follower level throughout its travel.<\/p>\n<\/div>\n

\n

\"Follower<\/source><\/source><\/source><\/source><\/picture>\nThis mag designed primarily for bolt-action rifles is not \u201canti-tilt.”<\/span><\/p>\n<\/div>\n

\n

The follower should also slide smoothly inside the body without getting hung up on anything. This is easy enough to test, but the real challenge comes when it gets dirty. Grit inside the magazine can cause the follower to seize up and stop working properly. Well-designed magazines have enough clearance between the follower and the body to allow for smooth operation even with some grit and grime.<\/p>\n<\/div>\n

\n

I\u2019d encourage you to put a magazine follower through its paces before taking it into the field. You might throw a mag into the dirt as if you dropped it by accident, load it up, and see if it functions. You might also make sure the rifle cycles smoothly with a fully loaded magazine and on the last round. These are the points at which a bad follower will rear its ugly head because the cartridge variance makes it difficult to maintain the correct upward pressure. I was recently testing a handgun and found that with hollow-point ammunition, the last cartridge always got stuck moving up the feed ramp. This kind of failure is usually resolved with a different magazine\u2014either a different brand or just a simple swap.<\/p>\n<\/div>\n

\n

Contrary to what you might think, springs don\u2019t wear out as the result of storing a magazine fully loaded. Springs primarily wear out through use\u2014by being compressed and decompressed again and again. Over time, they can no longer impart the force necessary to push the next cartridge into position at the correct time, which results in failures to load. This is a problem for semi-automatic rifles more than bolt-action rifles because unless you\u2019re some kind of wizard, you can\u2019t cycle the action faster than the mag spring can operate.<\/p>\n<\/div>\n

\n

A mag spring can also wear out thanks to rust, which is why good-quality magazines use stainless steel as the spring material.<\/p>\n<\/div>\n

\n

If the mag body gets dented, cracked, or otherwise deformed, the follower won\u2019t travel smoothly, and the mag will fail to function properly.<\/p>\n<\/div>\n

\n

Metal magazines are durable, especially steel varieties (as opposed to aluminum). They\u2019ve been proven over decades in the field, and the feed lips don\u2019t crack or wear out. However, once they get dented, the follower will bind, and they\u2019re pretty much useless.<\/p>\n<\/div>\n

\n

\"Body<\/source><\/source><\/source><\/source><\/picture><\/p>\n<\/div>\n

\n

Polymer magazines can have issues with the feed lips (depending on the construction quality), but the plastic offers better flexibility and impact resistance. The material \u201cbounces back,\u201d so to speak, which allows the mag to keep functioning even after receiving a blow. That doesn\u2019t mean they\u2019re invincible\u2014they can still crack and break. But the feed lips are more likely to fail than the body of the magazine itself.<\/p>\n<\/div>\n

Last Shot<\/h3>\n<\/p>\n
\n

Magazines can fail for other reasons, too. I once purchased a 30-round magazine for a 10\/22 that almost always caused feeding issues because it didn\u2019t fit securely in the receiver. It canted forward, which caused the rifle to jam every other round.<\/p>\n<\/div>\n

\n

But I think what I described above are four of the most common reasons. If that\u2019s the case, it follows that a high-quality rifle magazine does three things well:<\/p>\n<\/div>\n

\n